More on the results of vacuum pumps:

Heat Treating Steel - Hardening and Tempering

All heat treating of tese steels require a protective atmosphere (vacuum, inert gas or nitrogen). Heat slowly to 1700 to 1850°F, soak for up to 30 minutes, oil quench. temper at 400 to 1400°F. Cryogenic treatment improves this steel....<<more>>

Vacuum Melting Of Low Alloy Steel

The effect of vacuum melting on the elimination of gases and nonmetallic inclusions for six low-alloy steels was investigated. The purpose of these studies was the analysis and comparison of differences in gas content and inclusions in air-melted and vacuum-melted steel....<<more>>

Vertical aluminium alloy quenching furnace

Tube, Bar, Rod and Plate Extrusions Heat Treatment Solutions . Alternately, soft Alloys such as the 6000 series alloy 6061 can be T6 heat treated in gantry furnaces, tower drop bottom furnaces and more conventional batch drop bottom furnaces....<<more>>

Vacuum Heat Treating of Tool Steels : MoldMaking Technology

Vacuum Heat Treating of Tool Steels Tool steel refers to a variety of carbon and alloy steels that are particularly well-suited to be made into tools, however, special attention needs to be paid during their heat treatment so as to achieve the best properties for a given application....<<more>>

Alloy Steels, Tool Steels - Accurate Steel Treating

Accurate Steel Treating has specialized in commercial heat treating for over 54 44" Dia. Endo/Carburize Furnaces Nit 135 Mod Low Alloy High Strength Steels, Port Cap Forging, nitrided 15-5 PH Race/Rod End, Be-Cu Race Normalizing, Full Annealing Hardening (Q&T) Stress Relieving Vacuum Heat Treating (Oil, 6 Bar pressure) Finish Machined Parts ...<<more>>

Vacuum Quench Furnace for High Volume w Oil & Gas Multi

There are two types of CaseMaster Evolution. The two-chamber furnace, called D type, provides a dual-chamber vacuum-quench furnace with one for vacuum heat-treatment processing and a second chamber for oil or gas quenching....<<more>>

Gas Quenching - Steels, Heat Treatment, Case Study

Multi-chamber furnaces with high-pressure gas and oil quenching facilities are still available for the vacuum heat treatment of low-alloy steels. Heat treatments in salt baths and traditional protective-atmosphere furnaces are being replaced increasingly by processing in vacuum furnaces with high-pressure gas quenching, for a variety of reasons:...<<more>>

Vacuum Brazing - Aerobraze Engineered Technologies

A vacuum furnace is a furnace using low atmospheric pressures instead of a protective gas atmosphere like most heat treating furnaces. Furnaces are categorized as hot wall or cold wall, depending on the location of the heating and insulating components....<<more>>

Steels for Vacuum Carburizing - Industrial Heating

Steels for Vacuum Carburizing and Structure of the Carburizing Low Vacuum Carburizing special and high-alloy steels Currently, it is common to search for and apply new materials, especially in automotive and composition, are ideally suited to precision heat treatment carried out in vacuum furnaces. Gear wheels, pinions, drive system ...<<more>>

Crucible Tool Steel and Specialty Alloy General Information

The extended soak times depend on furnace equipment, load size and heat treat experience. Heat Treatment of Tool Steels: AISI: Preheat Temp. (1) In general, low alloy steels (O1) must be quenched in oil in order to cool fast enough. Vacuum heat treating may result in slightly lower hardness than achieved in a salt bath. Wrapping parts ...<<more>>

Hardening, Quenching, Tempering at Metlab of Wyndmoor PA.

Steel is essentially an alloy of iron and carbon; other steel alloys have other metal elements in solution. Heating the material above the critical temperature causes carbon and the other elements to go into solid solution....<<more>>

Controlled Atmospheres for Heat Treatment - 1st Edition

9.13.3 Vacuum Hardening of Low-Alloy Steels 9.13.4 Heat Treatment of Transformer Sheets 9.13.5 Combined Application of Vacuum and Protective Gas in the Heat Treatment of Copper Wires...<<more>>

Heat Treatment of Tool Steels in Vacuum Furnaces With Gas

The significance of vacuum furnaces in heat treatment has been increasing continuously and the area of tool steels has been of key importance for a few decades.kuzniapolska. 05. the process of heat treating tools and SW7M steel elements has been mastered and successfully applied in vacuum furnaces with gas quench in numerous other companies in ...<<more>>

Life Improvement of Alloys in Heat Treatment Furnaces and

Abstract Heat treatment furnace components and part holding fixtures are comprised of expensive heat-resistant alloys that are typically consumed in industry in less than three years, requiring frequent replacement....<<more>>

Heat Treatments Ltd - Heat Treatment Processes

Carbonitriding is a surface hardening treatment similar to carburising, however carbon and nitrogen are diffused into the surface of a low alloy/low carbon steel. This results in a component with a hard, wear resistant surface and a softer, tough core....<<more>>

Carburizing and nitriding - vacfurnace

Carburizing and nitriding generally refer to surface chemical heat treatment of steel.. Carburizing must be made of low carbon steel or low carbon alloy steel. It can be divided into solid, liquid and gas carburizing three kinds....<<more>>

Using Partial Pressure in Vacuum Furnaces

filler metal alloy can be avoided by raising the pressure in the Using Partial Pressure in Vacuum Furnaces 10 November 2005 – IndustrialHeating industrialheating:vacuum furnace, vacuum heat treating,vacuum brazing,vapor pressure,partial pressure,evaporation rate....<<more>>

Vacuum Annealing Furnace For High Speed Alloy Steel

Vacuum gas quenching furnace, heat treatement, hardening furnace. Vacuum Technology is the Basis for Process Innovation in Heat Treatment. Heat Treatment is the process in which metallic/steel parts are exposed completely or partially to time-temperature sequences in order to change the mechanical and/or corrosion properties....<<more>>

Metal Alloy Hardening - ThermTech

Oil Quenching. ThermTech is proud to offer oil quench hardening for steel castings. The process is typically employed on castings made from many low to medium- alloy steel grades with carbon in excess of .40%, or those with higher amounts of total alloy content....<<more>>

Different media for quenching metal explained | Paulo

Quenching metal is one of the critical stages in the heat treatment of a metal part because it’s during that process that added hardness is locked in. The concept is relatively simple: Heat a metal and then rapidly cool it to make it harder....<<more>>

A Simplified Guide to Heat Treating Tool Steels

A Simplified Guide to Heat Treating Tool Steels Classic symptoms of overheating are low as-quenched hardnesses and, depending upon the alloy content, shrinkage Obviously, vacuum heat treating furnaces do not allow quenching outside of the furnace unless the vacuum furnace...